Safety switches and circuit breakers inside a residential switchboard
Faults and safety

Safety switch keeps tripping: what to check before you call an electrician

A safety switch that keeps tripping has found a fault. How to find the appliance or circuit behind it, what not to do, and when to ring an electrician.

  • Licensed & insured
  • Local Frankston Team

Short answer

A safety switch trips when electricity is leaking to earth somewhere on its circuit. It is doing its job. Unplug everything on that circuit and reset it once. If it holds, plug things back in one at a time until it trips again. The last thing you plugged in is the fault.

If it will not reset with everything unplugged, the fault is in the wiring or in something wired in. Leave it off and ring a licensed electrician.

On this page
  1. What a safety switch does
  2. Reset it once
  3. Find what is tripping it
  4. What the pattern tells you
  5. When it trips with nothing plugged in
  6. What not to do
  7. When to ring an electrician
  8. One safety switch for the whole house
  9. If you rent
  10. Test your safety switches

What a safety switch does

A safety switch watches the current going out on a circuit and the current coming back. If some of it goes missing, it is leaking to earth, possibly through a person. The switch cuts the power. Energy Safe Victoria puts the time at within 0.03 of a second.

It is not the same thing as a circuit breaker.

Device What it protects What trips it
Safety switch (RCD) People, from electric shock Current leaking to earth
Circuit breaker The wiring, from overheating Too much load, or a short circuit
Combined device (RCBO) Both Either

A safety switch has a test button and “30mA” printed on it. If you are not sure your board has one, that is worth knowing before anything else. Boards in older houses around Frankston, Seaford and Carrum Downs often have one safety switch for the whole house, or none.

Reset it once

Go to the switchboard. Find the switch that is down or in the middle position. Push it fully off, then on.

If it stays on, note the date and what was running. One trip in a storm, or one trip in a year, is not a pattern.

If it trips again, do not keep resetting it. Every reset puts power back onto a faulty circuit.

Find what is tripping it

Most trips are caused by something plugged in. You can find it without tools.

  1. Work out which circuit is dead. Check which power points and lights have no power.
  2. Switch off and unplug everything on that circuit. Include the things you forget: the fridge, the dishwasher, the washing machine, the garage, the outdoor power points.
  3. Reset the safety switch.
  4. If it holds, plug things back in one at a time. Wait a minute between each.
  5. When it trips, the last thing you plugged in is the fault. Unplug it and leave it unplugged.

On a circuit with a fridge or an air conditioner, wait two or three minutes before each reset.

Do not put a faulty appliance back into service, and do not open it up. Energy Safe Victoria’s advice is that only a qualified repair technician or a licensed electrician repairs an appliance.

What the pattern tells you

When it trips Where the fault usually is
When one appliance is switched on That appliance. Kettles, toasters, irons, dishwashers and washing machines are common, because a heating element leaks current as it fails
After rain, or when the sprinklers run An outdoor power point, an outside light, a pump, or a fitting under a roof leak
At random, days apart A fridge or freezer on its cycle, a slow failure in a fixed appliance, or a damaged cable
Straight away, with everything unplugged The wiring, or something wired in such as an oven, a hot water unit or a light fitting
The whole house goes off One safety switch is covering every circuit. Any small fault takes everything out

The intermittent one is the version we see most. It goes off, you reset it, it is fine for a week, then it happens again. That pattern nearly always means moisture getting into something, an appliance failing slowly, or a cable that has been damaged. None of those fix themselves.

When it trips with nothing plugged in

Then the fault is in the fixed part of the house. That means the cable in the walls and roof, the power points and switches themselves, the light fittings, or an appliance that is wired in and has no plug.

You cannot test for this at home. It takes an insulation resistance tester, which measures how much current each cable leaks, circuit by circuit. Leave the safety switch off. The rest of the house can stay on.

What not to do

  • Do not keep resetting it to get through the evening.
  • Do not tape or wedge the switch on.
  • Do not use an appliance that tripped the switch or gave anyone a shock.
  • Do not take the cover off the switchboard. Energy Safe Victoria is blunt about home repairs: it is unsafe and illegal.
  • Do not touch a power point or switch that is cracked, loose or scorched. Cover it and have it replaced.

If you feel a tingle or a shock from a tap or an appliance, do not touch it again. Ring United Energy on 132 099 straight away, then ring an electrician. Energy Safe Victoria’s advice is to call the electricity company immediately and have a licensed electrician check the wiring.

When to ring an electrician

  • The safety switch will not reset with everything unplugged.
  • It trips again within days and you cannot tie it to one appliance.
  • There is a burning smell, a scorch mark, or a buzz or crackle at the switchboard.
  • Water has got into a fitting, a power point or the board.
  • The switch does not cut the power when you press the test button.

A burning smell or water near the power is urgent. Ring us on the number at the top of the page. For the rest, fault finding is a daytime job. We charge a fixed fee for the diagnosis and price the repair before we start it.

One safety switch for the whole house

If every trip takes out the whole house, the board has a single safety switch ahead of all the circuits. It also adds up the small leakage from every appliance in the house, so it trips more easily.

The fix is a combined safety switch and circuit breaker on each circuit. A fault then takes out one circuit and tells you which one. On an older board with no room, or with ceramic fuses, that means a switchboard upgrade. On a newer board we can usually add safety switches to what is there.

If you rent

Since 29 March 2023, every power outlet and lighting circuit in a Victorian rental must be connected to a circuit breaker and a safety switch at the switchboard. Tell your agent or rental provider about a safety switch that keeps tripping. Repairs to the wiring and the switchboard are theirs to arrange.

Rental providers must also have the electrical installation checked every two years. We do those safety checks and the repairs that come out of them.

Test your safety switches

Press the test button on each safety switch. The power on that circuit should cut at once. Push the switch back on.

Energy Safe Victoria’s “Test. Reset. Protect.” page says to do this every three months. If the power stays on when you press the button, the switch has failed. Ring a licensed electrician.

Sources

Read on 22 November 2026. Rules change. Check the linked page for the current wording.

Common questions

Is a safety switch that keeps tripping dangerous?
The switch is the safe part. It is cutting the power because current is leaking where it should not. The danger is the fault it has found, and in forcing the power back on without fixing it. Leave the circuit off until the cause is found.
Why does my safety switch trip when it rains?
Water is getting into something outside or in the roof. Outdoor power points, garden lights, pond and pool pumps, and light fittings under a leaking roof are the usual places. It dries out, the switch holds, and it trips again at the next rain. The fitting needs to be found and replaced or sealed.
Can a safety switch wear out?
Yes. Press the test button. If the power does not cut, the switch has failed and needs replacing. A switch can also pass the button test and still be too slow. An electrician measures the trip time with a tester.
What is the difference between a safety switch and a circuit breaker?
A circuit breaker protects the wiring. It trips on an overload or a short circuit. A safety switch protects people. It trips when current leaks to earth, which is what happens when someone gets a shock. A safety switch has a test button and 30mA printed on it. Many newer boards use one combined device per circuit.
Do you come out after hours for a safety switch that will not reset?
Yes, for urgent faults. We run after-hours call-outs across Frankston and the south-east. If the rest of the house has power and the dead circuit can wait, we book a daytime visit, which costs less.

What we can do

  • Electrical fault finding

    We test the circuit with instruments, find the cause and price the repair before we start. Fixed diagnosis fee.

    Electrical fault finding
  • Safety switch installation

    A safety switch on every circuit, so one fault takes out one circuit and not the house.

    Safety switch installation
  • Emergency electrician

    After-hours call-outs for urgent faults across Frankston and the south-east.

    Emergency electrician

More articles from the blog

Tell us what it is doing

Pick any
Your details

Talk to a licensed electrician

Based in Frankston North. Fixed price before we start. After-hours call-outs for urgent faults.